Tap Repairs in Kelvin Grove
Behind most tap repairs in Kelvin Grove sits one worn part, and the tap's design tells you which one. Twin-handle taps seal with a rubber washer; single-lever mixers seal with a ceramic disc cartridge.
If we're late, $100 comes off your bill
- Licensed and InsuredEvery job done by a licensed plumber. QBCC No: 15024607
- Fixed Quote FirstFlat-rate pricing, agreed before any work starts
- Lifetime Labour WarrantyBacked by our Fix-It-or-It's-Free guarantee (T&Cs apply)
- $0 Call-Out FeesNo extra charge for nights, weekends or public holidays
We replace both, along with O-rings, spindles and whole fittings, and every job is done by a licensed plumber. Even a slow drip pushes water through your meter day and night, so the yearly total on your account can sting.
This page explains what the repair involves, where Queensland law draws the DIY line, and when a tap has reached the end of its life. You can see the wider range of tap and toilet plumbing jobs we take, or read on for your particular drip.
How Tap Type Decides the Repair
A washer tap shuts off when its rubber washer presses onto a valve seat; a mixer shuts off on a ceramic disc cartridge inside the body. Knowing which design sits on your sink tells you what the repair involves before anyone opens a toolbox.
Washer taps
have two handles, hot and cold, each turning several full turns. The spindle screws down and drives the washer onto the seat to stop the flow. The jumper valve rides at the spindle's lower end and carries that washer.
Mixer taps
run hot and cold through one lever, usually with a quarter turn. Grit or wear in the cartridge or spindle makes the lever stiff or loose even while the tap still holds water. When a ceramic disc cartridge wears out, the whole cartridge comes out and a new one goes in, and each make and model takes its own fitting.
Still Dripping After You Turn It Off
Water dripping from the spout once the tap is fully closed means the part doing the sealing is worn or damaged. Where the water shows up tells you which part, because a spout drip, a handle leak and a wet base are three different faults.
From the spout
the washer or its seat on a twin-handle tap, or the cartridge on a mixer.
Around the handle while the tap runs
the O-ring or the spindle seal under that handle.
At the base or under the bench
O-rings gone hard, a connection below the tap that has worked loose, or corrosion eating through the body.
Before any of these get touched, the water needs isolating. An isolation valve at the fixture shuts just that tap off. Where there isn't one, the meter tap gets closed clockwise, after checking that nothing like the hot water system depends on that supply staying on.
A cistern that keeps refilling is a cousin of the same problem, and our toilet repairs page covers that fault on its own.
Tap Repairs for Owners and Tenants
Queensland splits tap work into three categories, and the boundaries surprise people. The QBCC lists the jumper valve and washer as unregulated work, which anyone with the knowledge and skill for it may do, provided the finished work still meets the standards. Everything past that point belongs to a licensed plumber.
Unregulated
replacing a tap jumper valve or washer, done to standard.
Minor work
every other tap repair, carried out by a QBCC licensee, with no permit applying and no Form 4 lodged.
Licensed work
fitting a whole new tap. The QBCC guide points to that very job when it explains what sits outside the home owner's list.
Renters have their own track. A leaking tap is not on the emergency list, so it counts as routine: the tenant reports it, and tenancy law has the owner or manager arrange the fix within a reasonable time. Form 11, the notice to remedy breach, gives the owner or manager at least seven days to act if nothing happens.
What Decides Repair or Replace
The price of a tap repair turns on the tap type, the part it needs, any seat or body damage, and how easily the water shuts off at the fixture. How many taps we do in one visit matters too. You get the figure in a fixed quote once we've seen the job.
Some taps are past repairing. The usual signs:
- a cracked or heavily corroded body;
- a valve seat too damaged for a new washer to seal against;
- a leak that survives new washers or cartridges.
At that point a replacement tap is the answer, and the plumbing side of toilet installation work runs on the same principle: the fixture is new, but the connections still belong to a licensed plumber.
What Kelvin Grove Housing Means for Taps
Most homes here are apartments, and the mix of tap designs follows that. Area-level figures put population growth at 14.8 percent over five years, while only 74 dwellings were approved in the same period, so the housing stock is largely established rather than new. That means plenty of mixers of a certain age, not fresh ones.
The apartment buildings around the urban village pack mixers, valves and hoses into tight cupboards, so a cartridge job often starts with careful isolation in a cramped vanity. The older cottages bring the opposite problem: worn brass spindles and seats that have seen decades of use, common in unrenovated places off Prospect Terrace.
How the Tap Repair Visit Runs
- 1
Call or message us
Ring (07) 3523 7121 or use the form and describe what's going on in Kelvin Grove. A few details up front mean the right gear comes on the first trip.
- 2
We diagnose the tap on the spot
We close the water at the fixture or the meter, strip the tap, and identify the worn part, the seat condition and the body's state before any work is agreed.
- 3
Fixed quote, then the work
We give you a fixed quote before any work starts. It's flat-rate pricing with no hidden fees, and we only start once you approve it.
- 4
Settle up your way
Card and EFTPOS payment on site when the job's finished, or Fix now, pay later if that suits you better.
Plumbing job in Kelvin Grove?
$0 call-out fees, available 24/7, and same-day where we can.
Tap Questions Kelvin Grove Locals Ask
Call (07) 3523 7121How do I stop my tap dripping in Kelvin Grove?
Find the sealing part first. A twin-handle tap needs a washer or jumper valve, and a mixer needs a new cartridge. Queensland lets anyone with the knowledge and skill replace a jumper valve or washer, provided the work meets the standards; every other tap repair belongs to a licensed plumber.
Why does my tap keep dripping when it's turned off?
The sealing part has worn out, or the seat it presses against is damaged. For twin handles that means the washer, the jumper valve or the valve seat. On a mixer it means the ceramic disc cartridge, which gets replaced as a whole unit.
What makes a mixer tap leak around the base?
Usually worn O-rings, a fitting under the mixer that has loosened, or corrosion that has split the body. A licensed plumber isolates the water, strips the mixer and identifies which of the three it is before quoting the fix.
Does fixing a tap need a permit or a Form 4?
No. Tap repairs other than the washer or jumper valve count as minor work done by a licensed plumber, and minor work needs no permit and no Form 4. Replacing a jumper valve or washer yourself needs no approval or report either, as long as the work meets the standards.
How much does it cost to fix a leaking tap in Kelvin Grove?
The price depends on the tap type, the part it needs, any seat or body damage, and how easily the water shuts off at the fixture. You get a fixed quote before any work starts, once the tap has been inspected.
Call Us About That Dripping TapWe'll call you back.
Ring (07) 3523 7121 and tell us what's wrong. You get $0 call-out fees, a fixed quote before any work starts and same-day where we can, 7 days a week.
To claim your $0 call-out fee, call (07) 3523 7121 today.